Anfänger mit Motorenproblem

  • Hallo


    Zu meiner Person, ich heiße Frank bin 41 Jahre und komme aus dem Raum Bingen am Rhein.


    Mein Problem, das wohl jeder Anfänger hat, sind die Motoren. Die machen keinen Mucks.
    Folgende Komponenten sind verbaut:


    4x Suppo 2212 Motoren
    4x Modelcraft Regler 20 A
    FC MultiWii SE 2.0 Crius
    MultiWii 2.2 aufgespielt
    Empfänger Spektrum AR 500
    Regler sind angelernt und die Combos funktionieren einwandfrei direkt am Empfänger.
    Sobald alles am FC ist, ist es vorbei. Motoren piepsen 3 mal.
    Scharfschalten ist auch nicht.
    In der MINCOMMAND habe ich einige Werte versucht, erfolglos.
    Im MultiWii Configtool werden aber alle Steuerbefehle korrekt angezeigt.


    /**************************** Motor minthrottle *******************************/
    /* Set the minimum throttle command sent to the ESC (Electronic Speed Controller)
    This is the minimum value that allow motors to run at a idle speed */
    //#define MINTHROTTLE 1300 // for Turnigy Plush ESCs 10A
    //#define MINTHROTTLE 1120 // for Super Simple ESCs 10A
    //#define MINTHROTTLE 1064 // special ESC (simonk)
    //#define MINTHROTTLE 1050 // for brushed ESCs like ladybird
    #define MINTHROTTLE 1050
    // (*)


    /**************************** Motor maxthrottle *******************************/
    /* this is the maximum value for the ESCs at full power, this value can be increased up to 2000 */
    #define MAXTHROTTLE 1850


    /**************************** Mincommand *******************************/
    /* this is the value for the ESCs when they are not armed
    in some cases, this value must be lowered down to 900 for some specific ESCs, otherwise they failed to initiate */
    #define MINCOMMAND 960


    /********************************** I2C speed ************************************/
    #define I2C_SPEED 100000L //100kHz normal mode, this value must be used for a genuine WMP
    //#define I2C_SPEED 400000L //400kHz fast mode, it works only with some WMP clones


    /*************************** Internal i2c Pullups ********************************/
    /* enable internal I2C pull ups (in most cases it is better to use external pullups) */
    #define INTERNAL_I2C_PULLUPS

  • AW: Anfänger mit Motorenproblem


    Wie siehts in der MultiWiiConf aus?
    Alle Endpoints der Kanäle unter 1100 und über 1900?

    Da alle Modelle nicht mehr aufzählbar sind, um sie hier zu zeigen.. Meine RC Modelle in Übersicht.
    Carbon Breaker, Carson Attack, FG Glattbahn, Reely Rex X, TS4-N Pro V2, AMG Mercedes.
    zuendy.de

  • AW: Anfänger mit Motorenproblem


    Teste mal bitte noch die Multiwii 2.1. Gab schon den ein oder anderen hier mit Problemen.


    Vorher aber ein EEPROM_CLEAR durchführen.


    Findest du im Arduino Programm unter:


    - Datei
    - Beispiele
    - EEPROM

  • AW: Anfänger mit Motorenproblem


    Gerade wenn man von 2.2 zurückflashed da geht nix mehr. :D



    Da wo Throttle Pitch YAW Roll steht


    Muss wenn du die Knüppel los läßt um die 1500 stehen.
    Als min. Werte <1100
    Als max. Werte >1900
    Also bei maximalen Ausschlag der Knüppel in alle Richtungen.

  • AW: Anfänger mit Motorenproblem


    Auch mit der der 2.1. bleiben die Motoren still.
    Grundsätzlich hab ich nur den Coptertyp, Board, MINCOMMAND und GPS eingestellt.
    Hab ich da irgendetwas vergessen?

  • AW: Anfänger mit Motorenproblem


    Das Problem hatte ich mit meiner Hitec und musste das da umstellen:


    // ******************
    // rc functions
    // ******************
    #define MINCHECK 1150
    #define MAXCHECK 1830




    **************************** Motor minthrottle *******************************/
    /* Set the minimum throttle command sent to the ESC (Electronic Speed Controller)
    This is the minimum value that allow motors to run at a idle speed */
    //#define MINTHROTTLE 1300 // for Turnigy Plush ESCs 10A
    //#define MINTHROTTLE 1120 // for Super Simple ESCs 10A
    //#define MINTHROTTLE 1064 // special ESC (simonk)
    //#define MINTHROTTLE 1050 // for brushed ESCs like ladybird
    #define MINTHROTTLE 1150 // (*)


    /**************************** Motor maxthrottle *******************************/
    /* this is the maximum value for the ESCs at full power, this value can be increased up to 2000 */
    #define MAXTHROTTLE 1850


    /**************************** Mincommand *******************************/
    /* this is the value for the ESCs when they are not armed
    in some cases, this value must be lowered down to 900 for some specific ESCs, otherwise they failed to initiate */
    #define MINCOMMAND 1035



    Da musste einfach mal mit den Werten spielen ..

  • AW: Anfänger mit Motorenproblem


    Nein, der ist im Multiwii Reiter ganz oben links.


    Du kannst auch testweise ohne Propeller, den Arm als Schalter defibnieren.. dann weisst Du ob´s uberhaupt funktioniert.

  • AW: Anfänger mit Motorenproblem


    Hey hat geklappt, Motoren laufen.
    Aber der Motor Hinten Links fängt erst bei Vollgas an zu laufen und stoppt auch direkt bei minimaler Gasrücknahme.
    Ansonsten dreht Vorne Rechts auch nicht gleichmäßig mit dem VL und HR.

  • AW: Anfänger mit Motorenproblem


    Hast Du die Regler alle angelernt?


    Regler an Throttle Kanal, vorher die Funke einschalten und Vollgas geben.
    Lipo ohne FC anschliessen, nur Regler und Motor und den Initial Beep abwarten.
    Danach gehst Du auf Minumum Gas, erneuter Ton... dann ist er angelernt.

  • AW: Anfänger mit Motorenproblem


    Ja aber ich machs nochmal, hab 300u/min weniger auf LH.
    Aber ich hab nochmals rumgetüfftelt, alle Regler haben direkt am Empfänger korrekt funktioniert. Sobald sie am FC hängen ist der Unterschied da, LH und RV laufen nicht korrekt.
    Und warum die Motoren auch nicht ansprangen war die Tatsache das alle Steuerbefehle auf 100% standen. Erst als ich alle auf 125% hatte, ging die Drehorgel los.
    Ich hatte nur testweise mal Throttle auf 125% gestellt, oh mann...


    Also, der Drehzahlunterschied kommt vom FC, ich habe die Regler alle mal vertauscht und bekomme immer an den besagten eine Drehzahldifferenz.

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!